Jump to content

No$GBA 2.4d released


Robert

Recommended Posts

GBA/NDS emulator

 

21 August 2007 - version 2.4d

 

No$gba v2.4d lots of new info on wifi and ds-lite

(*) no$gba/wifi can send/receive packets, commercial programs are still getting stuck somewhere in transmission. NEW in v2.4d: Pictochat is now successfully exchanging authentication and associations requests and responses. After that, on real hardware, the host should immediately send data frames (via port 090h presumably), in no$gba, the host doesn't send any such data frames for whatever reason (only the client does, via port 094h). Info on fixing that problem would be highly welcome. Built-in help text (in debug ver) contains almost complete wifi specs now.

 

- debug/setup: allows to enable/disable user-debugmsg, wifi-log, and 3d-log

- cpu: emulates undef opcode/copro exception (with warning if no bios/vector=0)

- wifi/emu: emulates new bits in rx header, and optional auto sequence control

- cpu/bugfix: arm ldm/stm accidently destroyed mis-alignments (on writeback)

- wifi/help: added info on port 1C4h, and on some of the 1Bxh ports (rxstat's)

- wifi/help: added new chapter on transmit errors and automatic ACK responses

- wifi/help: added info on ports 1A8h,1AAh,1ACh,1AEh (bit0..12 vs. 1B0h..1BFh)

- wifi/help: discovered new bits in RX header, added notes on MAC addresses

- wifi/debug: allows to log all packets (with automatic comments on ieee header)

- wifi/help: added notes on automatic sequence ctrl and auto-modified frame ctrl

- wifi/emu: tx-engine uses new timers, and emulates length/rate/preamble timing

- wifi/emu: emulates the various wifi counters and irqs at correct timing

- debug/setup: memorizes if iomap window was open (if so, re-opens it on boot)

- debug/emustop: break_requests (esc-key) take place only on current machine

- debug/internal: replaced ds:bibos swi_retadr/haltstop/intrwait by vals:bios

- debug/vramviewer: oam viewer supports extended obj palettes (thanks pierre)

- debug/vramviewer: fixed engine-B palette viewer (thanks pierre for bug report)

- dslite/help: added info on new TSC chip by AKM (new IN2, different PD bits)

- dslite/help: added note on near-crt-quality colors and wider viewing angles

- dslite/help: added custom change-channels-flowchart for new wifi-type3-chips

- dslite/help: added settings at firmware[0CEh-and-up] for new wifi-type3-chips

- dslite/xboo: updated nds-pins.gif (added new pin-positions on ds-lite board)

- dslite/xboo: added 8 extra diodes in data lines (to prevent power-on problem)

- dslite/help: added lite-specific wifi (W) mirrors, and unused wifi ram/ports

- dslite/help: added the new backlight level bits in firmware user settings

- dslite/help: added caution on DS-lite destroying wifi ports 064h and 076h

- dslite/help: added new powerman backlight/power register (and lost mute-bit)

- dslite/help: added ID for firmare chip 35PE20P (and supported it in ds-xboo)

- powerman/help: added unknown bit (mutes volume to zero, if amplifier is on)

- wifi/emu: emulates initial wifi-port settings and random register (mod 5FDh)

- wifi/emu: emulates primary wifi irq flag stuck zero while secondary nonzero

- wifi/emu: emulates corrected ports (004h,0ACh,0AEh,0B0h,0B4h)

- wifi/emu: emulates new ports (210h, 05Ch/06Ch, 062h/064h) and new mirrors

- wifi/help: added rx/tx signal/timing charts (rfu pins, aka 19Ch bits)

- wifi/help: added specs/cautions on primary wifi irq flag (2000214h.Bit24)

- wifi/help: added new mirrors (on read from 0ACh,0AEh,20Ch,21Ch,298h,2A8h,2B0h)

- wifi/help: added notes/info on ports 038h,19Ch,214h,21Ch and on W_CONFIG_140h

- wifi/help: new bits 0EAh.1,008h.13/14 004h.14); extra-TX ports 118h,0EEh,090h

- wifi/help: corrected ports 004h,0ACh,0AEh,0B0h,0B4h and txstat.bit12-13

- wifi/help: added info on new ports (110h, 210h, 05Ch/06Ch, 062h/064h)

- wifi/help: fixed tx_hdr: rate 8bit (not 16bit) defaults to 1Mbit/s if invalid

- wifi/help: added new bits: port004h.bit0 tx_master, 008h.bit15 beacon_irq1

- wifi/help: major updates in timers chapter (reloads, IRQ13/14/15, 22MHz, etc)

- nds/help: pinouts for nds LCD sockets, wifi RFU boards, and powerman chips

- gui: mousewheel support (win98 or dos/ctmouse) (thanks jasper/idea, tilo/hw)

Changelog / Download

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...